Self-Furring Dimpled Diamond Mesh Lath is used over solid surfaces like concrete, cement board, column fireproofing, masonry and replastering over old surfaces. The self-furring dimples hold the metal lath 1/4″ away from the surface to be plastered.

What does self-furring mean?

Said of metal lath or welded wire fabric having some means of spacing it from a wall; when plaster, stucco, or concrete is applied to the fabric, the space makes it possible to key, 8 the applied material to the metal lath or welded wire fabric.

What is lath and furring?

The origin of the furring strip may be from the root "furr", which is the term given to the space behind the field of lath. Metal furring strips are used for commercial projects, or in towns where fire-proof supporting elements are required by the local building code.

What are lath used for?

Lath, any material fastened to the structural members of a building to provide a base for plaster. Lath can be of wood, metal, gypsum, or insulated board. In older residential buildings, narrow wood strips were generally used.

What does metal lath do?

Metal lath is used to prevent or decrease wall crackings in either pumped or troweled application. Sheet metal lath is slit and expanded into small diamond openings (approximately 11,000 per square yard).

stucco netting 17 gauge galvanized woven wire for stucco, deep or Self-furring Stucco Netting

27 related questions found

What is K lath?

K-LATH^® is the leader in reinforcement for stucco walls and cladding. Since 1944, K-LATH^® has produced welded wire and paper-backed reinforcing products for the stucco industry. Indeed the name "K-LATH^®" has become a generic term for describing proper stucco reinforcing.

How do you attach metal lath?

For the metal lath, attach 2.5 lb. expanded, galvanized, metal lath to each stud 6” on center-vertically, penetrating the studs at least one inch. Be sure to attach the lath horizontally. The surface should feel rough as you rub your hand upward.

Why is it called lath?

The name derived from the spreading action, which is like pulling an accordion open. After the circular saw came into use in the early 19th century, lath for plastering was sawn in sawmills and delivered to the building site.

What does lath look like?

These are narrow strips of wood, extruded metal, or split boards, nailed horizontally across the wall studs or ceiling joists. Each wall frame is covered in lath, tacked at the studs. Wood lath is typically about one inch (2.5 cm) wide by four feet (1.22 meters) long by 1⁄4 inch (6.4 mm) thick.

What kind of wood is lath?

The majority of lathe boards are now made from cedar. It is light, affordable and highly resistant to rot or decay, making it a perfect choice for any outdoor application. Cedar has a rough texture that implies rugged beauty.

What is a furring piece?

A firring is a thin strip of timber (or 'batten') that has been cut along its length diagonally so that it tapers, with one end deeper than the other. ... Firrings are sometimes referred to as furring strips or furrings.

What are furring nails used for?

For attaching stucco wire mesh to exterior of structure in preparation for the application of stucco mud. Nail with wad used with paper that does not have wadding preattached.

What does Furr out mean?

For people who are unfamiliar with this term, a furr out wall is when you expand the thickness of a wall using furring strips. Some people refer to this as building one wall inside of another.

Which direction do you install metal lath?

Metal lath should be hung horizontally. Joints between panels should be staggered in a standard brick-laying pattern. The seam between the first and second panels on the bottom of the wall should fall in the center of the panel placed immediately above them.

What is lath in stucco?

Lath is simply the first step in the stucco process. It consists of water resistant paper, (sometimes eps foam) wire and other metal components that make up the essential “framework” for the cement to be adhered to. It attaches to the substrate and is the structure for the following coats.

Can you use chicken wire for stucco?

There is really only one style and it resembles the look and thickness of traditional chicken wire. This is really the only type of wire that is used for a one coat stucco installation and the wire is made specifically for it too, so keep that in mind.

What is plaster Paris?

plaster of paris, quick-setting gypsum plaster consisting of a fine white powder (calcium sulfate hemihydrate), which hardens when moistened and allowed to dry. Known since ancient times, plaster of paris is so called because of its preparation from the abundant gypsum found near Paris.

Does Walabot work on plaster walls?

The Walabot DIY can be used on drywall and concrete walls. It does not work on lath and plaster walls.

Can you board over lath and plaster?

To be done properly the lath and plaster ceiling really needs to be pulled down and re-boarded directly on to the ceiling joists with 12.5mm plasterboards. You must however make sure the artex on the ceiling does not have any asbestos in it as pre 1980 may very well be artex that used asbestos.

What is redwood lath used for?

Redwood lath is great for fencing, trellises, and custom latticing. Natural redwood weathers beautifully and naturally when used in outdoor projects. Redwood lath is great for fencing, trellises, and custom latticing. Natural redwood weathers beautifully and naturally when used in outdoor projects.

How do I know if my ceiling is lath or plaster?

How to check for lath and plaster. In older properties you can check the type of ceiling by looking under the loft insulation, or lifting a bedroom floorboard. If there are lots of small timber laths with creamy lugs of plaster in between, the ceiling is original.

How was wood lath installed?

Builders nailed thin, closely spaced strips of wood (lath) to wall studs and then smoothed multiple coatings of plaster over the lath to form flat wall surfaces. When drywall panels came on the scene in the 1950s, they soon replaced lath and plaster as a quicker, easier install option.

How do you fasten lath to block?

Hold the lath against the wall with the diamonds created from expanding the mesh pointed upward. Secure it in place using 7/8-inch concrete nails with a washer over the nail shaft to hold down the mesh strands. Drive the nails through the mesh into the concrete wall using a hammer.

What is the best way to cut metal lath?

Cut Metal Lath and Mesh with a Grinder

Mount a diamond blade in your angle grinder and use it like a saw to cut the mesh. We recommend using a diamond blade that's labeled as a ferrous-metal-cutting blade, but many tradespeople use a regular masonry diamond blade with good results.